Popis předmětu - AE4B38NVS

Přehled studia | Přehled oborů | Všechny skupiny předmětů | Všechny předměty | Seznam rolí | Vysvětlivky               Návod
AE4B38NVS Embedded Systems Design
Role:  Rozsah výuky:2P+2L
Katedra:13138 Jazyk výuky:EN
Garanti:  Zakončení:Z,ZK
Přednášející:  Kreditů:6
Cvičící:  Semestr:L

Webová stránka:

https://moodle.fel.cvut.cz/courses/a4b38nvs http://measure.feld.cvut.cz/vyuka/predmety/A4B38NVS

Anotace:

The main aim of this subject is design of embeded systems using microcontrollers. It is mainly focused on 32-bit (alter. 8-bit) microcontrollers and DSP, supporting logic devices, external input/output devices and the other supporting devices.

Osnovy přednášek:

1. Blocks of a embedded system
2. Microcontrollers, their peripherals, buses, digital signal processors
3. Microcontrollers used for laboratory experiments, interface, signals, timing
4. Logic devices, parameters, power consumption, grounding
5. Memories, RW-SRAM, FIFO, Duala ported, SDRAM, stucture, timing
6. Nonvolatile memories ROM, MASK ROM, EPROM, FLASH - NOR, NAND, memory cards
7. Input/output port, peripheral controllers interfacing (USAT, EThernet, CAN)
8. Interfacing - push buttons, keyboard, touch screen
9. Embedded system design - bus timing, CPU to memory and I/O interfacing
10. Dynamicaly controlled LED display, graphical LCD interfacing
11. Timers, input capture, output compare modul, PWM, driving of power outputs
12. Supervisory devices, watch dog, power supply for embedded system, battery powering
13. Cooperation of microcontrollers in an embedded system
14. Case study

Osnovy cvičení:

1. Introduction, IDE for ARM Cortex M3 (STM32)
2. Compiling, debugging
3. Reading of input pins, push button interfacing, keyboard
4. Output port interfacing, LEDs and stepper motor driwing
5. Character LCD interfacing
6. Serial communication, use of a UART
7. Use of a SPI - Serial peripheral interface, input/output connecting
8. Inter integrated circuits bus - IIC, memory and supervisory device interfacing
9. Use of timers, input capture and output compare unit, PWM generation
10. Project specification design of a DAQ (data acquisition system), analysis
11. Project - solution: keyboard and LED interfacing + programs
12. Project - solution: use of a ADC, LCD interfacing + programs
13. Project - solution: program debugging
14. Project - final presentation, evaluation

Literatura:

[1] Balch, M.: COMPLETE DIGITAL DESIGN. A Comprehensive Guide to Digital Electronics and Computer System Architecture, McGRAW-HILL,2004, ISBN: 978-0071409278
[2] Yiu, J.: The Definitive Guide to the ARM Cortex- M3. Elsevier, 2007, ISBN: 978-0-7506-8534-4
[3] Sloss, A., Symes, D.,Wright, Ch.: ARM System Developer's Guide, Elesevier 2004, ISBN 1-55860-874-5

Požadavky:

Poznámka:

Rozsah výuky v kombinované formě studia: 14p+6l

Předmět je zahrnut do těchto studijních plánů:

Plán Obor Role Dop. semestr


Stránka vytvořena 29.3.2024 07:54:26, semestry: Z/2024-5, Z,L/2023-4, připomínky k informační náplni zasílejte správci studijních plánů Návrh a realizace: I. Halaška (K336), J. Novák (K336)